The basic model has a suction capacity of 2500 m³/h, a 3-year warranty and can withstand up to 300 degrees.
The professional model can withstand up to 700 degrees (therefore also in case of a chimney fire) and is recommended if you have a chimney of less than 3 meters. It also has a 6-year warranty and sucks in 3800 m³/h.
The steel model is built entirely in Aisi 304 stainless steel, a material that ensures greater resistance to corrosion and saltiness and therefore over time. It has a suction power of 3800m³/h and a resistance of up to 700°, guaranteed for 8 years.
The top of the range offered by Gemi is the professional copper model, resistant up to 700°, with a 10-year warranty and capable of sucking up 3800 m³/h. The stainless steel fan resists corrosion and saltiness. It is fully painted on the outside (including the base) and is therefore suitable for those looking for a more aesthetically pleasing product.
Chimney fan basic model
Chimney fan basic model The Gemi basic chimney fan is the entry-level model in a range built in Italy since 1983. Constructed from galvanised sheet steel with an adjustable base ring that spans all standard round and square flue terminal sizes, it resolves smoke problems in fireplaces,… Read more
Chimney fan basic model
The Gemi basic chimney fan is the entry-level model in a range built in Italy since 1983. Constructed from galvanised sheet steel with an adjustable base ring that spans all standard round and square flue terminal sizes, it resolves smoke problems in fireplaces, wood-burning stoves, pizza ovens and barbecues with a straightforward installation that requires no masonry work and no specialist tools. The basic model is the entry point to the Gemi chimney fan range and the most widely installed model across UK residential applications. It ships complete with the variable speed controller, heat-resistant cable and full installation instructions.
Technical specification
The basic model delivers 2,500 m³/h maximum extraction capacity and is rated for continuous operation at flue gas temperatures up to 300°C — sufficient for all wood-burning appliances in normal use. The variable speed controller supplied with every unit provides six selectable speeds, allowing extraction rate to be matched to fire intensity and ambient draught conditions without switching the fan off between adjustments.
Adjustable to all flue sizes
The expanding base ring adjusts incrementally to fit round flue terminals from the smallest standard size up to large inglenook openings. The same adjustment accommodates square section terminals using the included adaptor segments, making the basic model compatible with virtually every existing residential chimney configuration in the UK without additional parts.
Simple installation in under an hour
The fan unit mounts on the existing chimney pot or liner cap at roof level. The heat-resistant connection cable runs down the stack exterior or inside the flue to the controller positioned near the fireplace. Most installers complete the full installation — fan positioning, cable routing and controller wiring — within an hour on a straightforward residential chimney.
UK delivery in 24–48h — factory direct
The basic chimney fan is sold direct from Gemi Elettronica at manufacturer's price, including the variable speed controller and heat-resistant cable. UK delivery in 24–48h with full order tracking.
Questions and Answers
Our electric smoke extractor has a 6-speed regulator, so you only need to set it to speeds of 1-2 to help extract smoke naturally, but not heat.
Basically, at the first two speeds, we are not altering in any way the normal operation of a fireplace, which would normally disperse a very small amount of heat in the smoke rising in the flue pipe. The Gemi chimney fan sucks up the smoke that would otherwise go into the house and therefore, certainly, would not produce any heat sources for the indoor environment.
It is clear that if the chimney fan does not operate at the sixth speed (usually at this speed it is used to change the air in rooms, to help start fires or to suck up the ashes), with its 2500m³/h(basic) - 3800m³/h(pro) it will be so powerful that it will also suck up the heat, because it will increase the speed of combustion of the wood and consequently partially reduce the heat. Scientific studies have shown that the Gemi smoke extractor can control heat loss, so it is advisable to use a chimney to prevent heat loss.
This can be seen in the millions of satisfied customers all over the world since 1983, when the first Gemi chimney fan was created.
The base of the electric chimney fan is standard 43x43 cm, the height is 35 cm, without the brackets. Considering the brackets it is 50 cm. For more specific measurements, a diagram showing the measurements of each individual part of the electric fireplace extractor fan is available on our website.
The function of the smoke extractor is to regulate the draught of the chimney, in order to solve the problem of smoke in the chimney, oven, stove, barbecue and to reproduce the natural draught of the chimney.
The assembly of the chimney smoke extractor is do-it-yourself. Watch the tutorial video on the product sheets to assembly the chimney fan.
If you encounter problems with the installation of the extractor fan, you can ask for the help of an electrician or a bricklayer.
If you have any doubts about the installation of the product (e.g. connection of wires, speed regulator, etc.) our specialist technicians will be at your disposal via email, chat or telephone.
If you have a square chimney with a pipe of the same height as the masonry, you must first close the gap between the pipe and the masonry and then install the chimney fan directly on the masonry. Similarly, if the pipe is only a few centimeters (or inches) high, the pipe must be brought to the same height as the masonry.
In this situation you have to buy the model of chimney fan with square base, adjustable also for rectangular chimney.
It is possible, but you have to consider the dimensions of the chimney fan. The installation of the smoke exhauster can be done in two ways: eliminating the cap of the chimney and then installing the chimney fan, or inserting inside the chimney the chimney smoke extractor, ordering in this case the smoke extractor without the cap.
Yes, it is possible. There are two ways to make the electrical connection: with the 3 x 1.5 cable (to be run outside the chimney up to the speed regulator) in order to extend the first metre attached to the chimney fan.
Or you can make an internal connection to the chimney with our high-temperature resistant cable, which you can purchase separately by selecting the desired quantity in the drop-down menu according to how many meters you need.
There is no time limit. The chimney smoke extractor can work all day without any problem.
The professional fan for fireplaces can be installed at any height, even on flues of 1 meter. On the other hand, the basic model of the chimney fan is recommended for chimneys over 3 m high.